Floors & tiles / Worked planning example
Measure an L-shaped floor and compare whole-pack costs
Work from a 16 m² room sketch to whole packs, then compare real pack prices without hiding rounding.
An L-shaped room is easier to estimate when you divide it into rectangles that meet at an edge. The common mistake is measuring two large overlapping rectangles and adding both areas. This guide uses a simple labelled plan, follows two different pack sizes through rounding, and gives you a price comparison you can change.
The dimensions and pack sizes below are invented examples. They explain quantity planning, not a plank layout or an installation method.
1. Split the shape once
Rectangle A is 4 × 3 = 12 m². Rectangle B is the remaining 2 × 2 = 4 m². Total floor area is 16 m². Enter A and B as separate areas in the flooring calculator; it adds them before rounding packs.
You can cross-check the sketch another way: the outside rectangle is 4 × 5 = 20 m², and the missing corner is 2 × 2 = 4 m². Subtracting gives the same 16 m². The subtraction method is a paper cross-check; the calculator takes positive rectangular areas, so enter A and B rather than a negative “missing” room.
Measure the actual flooring footprint. Decide explicitly whether a cupboard interior or connected alcove receives the same product. Include an alcove only once and write its measurements on the drawing. Measure door recesses if they need covering. Do not subtract small obstacles automatically when usable cut pieces may still be needed around them.
2. Round the combined order
Choose a cutting allowance appropriate to the actual product, room and layout. The following 10% is an example for comparison, not a universal recommendation. Order area = 16 × 1.10 = 17.6 m². Divide that by the coverage printed on one pack and round up to a whole pack.
| Example product | Pack coverage | Packs | Purchased area | Above 17.6 m² target |
|---|---|---|---|---|
| A | 2.2 m² | 8 | 17.6 m² | 0 m² |
| B | 2.4 m² | 8 | 19.2 m² | 1.6 m² |
The exact boundary matters: eight 2.2 m² packs meet 17.6 m². If your confirmed area or allowance makes the target even slightly larger, a ninth pack is required. Do not round the measured area down to force an order into eight packs.
With no allowance, product A would require eight packs anyway (16 ÷ 2.2 rounds up). That does not mean cutting waste is always covered by pack rounding. In another room, the gap between the measured area and purchased area could be much smaller. Keep the chosen allowance visible instead of guessing that a spare pack “should be enough”.
Pooling is valid only for interchangeable material. If each rectangle needs a different product, round its packs separately. For product A with 10% allowance, separate orders for A and B require six plus two packs. For product B, they require six plus two as well, but other dimensions can create additional rounding losses. Keep batch and product requirements with the order.
3. Compare pack costs
A low price per pack is not enough to choose between products with different coverage. Compare the complete number of packs your project requires. The comparison starts with the 16 m² example floor. Replace the measured area with your own combined floor area, then enter each product’s pack coverage, price and your chosen allowance. Round packs after combining only areas that use the same interchangeable material. Prices are illustrative numbers in whichever single currency you enter for both products. Delivery, tax not already in the price, underlay and accessories are excluded.
| Product | Packs × price | Purchase total | Total ÷ measured 16 m² |
|---|---|---|---|
| A | 8 × 55 | 440 | 27.50 per m² |
| B | 8 × 58 | 464 | 29.00 per m² |
The cost per measured square metre spreads the entire pack purchase across the floor you actually cover. It differs from the label’s price per square metre because it includes allowance and whole-pack rounding. It is a quantity comparison, not a judgement about durability, suitability or product quality. A cheaper total cannot tell you whether a floor is appropriate for your room.
4. Check what area cannot tell you
An area estimate does not model each plank cut. Board direction, starter rows, pattern matching, minimum end pieces and joins can change usable yield. For installation requirements, use your exact product’s instructions; Quick-Step’s laminate installation resources illustrate why product-specific guidance matters. Room & Root is independent of the manufacturer.
- Record the product code and coverage from the pack you will receive, not a similar listing.
- Ask the supplier to confirm layout-specific allowance and whether unopened packs can be returned.
- List underlay, trims, transitions and other accessories separately; their quantities are not included in the pack estimate.
- If choosing tiles instead, use the tile calculator with tile dimensions and pieces per box. Plank packs and tile boxes are different inputs.
- Keep the final sketch and order together. If a dimension changes, recalculate before buying.
Your flooring measurement sheet
Print this page and fill in your own measurements. This sheet does not save or submit any information.
| Record | Your measurements or choice |
|---|---|
| Sketch reference and non-overlapping areas | |
| Each rectangle: length × width | |
| Total measured area | |
| Product code and coverage per pack | |
| Layout and chosen cutting allowance | |
| Required area before pack rounding | |
| Whole packs × actual price | |
| Accessory list / return conditions |
Plan before you buy
Worked project guides
Follow the measurements through to a practical order.
Walls & ceilings
Plan paint for two rooms without mixing up products
Separate wall and ceiling products, measure openings, and see why a small coverage change can mean another tin.
Floors & tiles
Measure an L-shaped floor and compare whole-pack costs
Work from a 16 m² room sketch to whole packs, then compare real pack prices without hiding rounding.
Beds & borders
Plan raised-bed fill and compare bags with bulk
Use internal bed dimensions, separate material layers, and compare bag rounding with supplier bulk increments.